Product Description
Boat model | 45ft | Displacement | 10Ton |
Length | 13.60m | Max people | 12 |
Beam | 4.10m | Engines | da 2 x 330 HP |
Certificate | Available | Material | Fiberglass |
The boat is built with reinforced fiberglass , CE homologated , with deep V hull and with a very good speed performance and sea keeping at medium sea conditions.
The deck is insulated against heat and noise by the foam inside the sandwich structure . Particular attention has been paid to the nautical characteristics of the boat , whose hull’s lines allow her to obtain very good cruising speeds already with a total power installed of 1000 Hp .
A good manoeuvrability is assured by means of twins rudders in stainless steel installed under the bottom .
On the aft a swim platform is moulded integrated in the hull , this platform is of a big size and it is very reachable in a very easy way trough a passage from the cockpit , the area of the platform is also used for the dinghy storage .
The strength of the hull structures is such to allow the boat to navigate even with bad sea and weather conditions .
The interior furniture are in Cherry wood and the tissues for sofa , curtains , bed covers etc are at choice from the shipyard catalogues .
All the cabins are supplied with carpets at choice from catalogue .
Engine supports in light alloy and steel
N.2 fuel tanks in light alloy
N.2 fuel filters Racor type
N.2 sea water inlet 2” with filters and valve with safety by-pass for bilge suction
N.2 exhaust silencers
Exhaust manifolds
Sea-water cooling circuit built and installed inside stainless steel box
N.2 stuffing boxes
N.2 stainless steel rudders vertical at hull
N.2 base struts
N.2 axis
N.2 coupling flanges for engine inverter
N.2 four blade propellers
Coupling bar for rudders
N.1 hydraulic cylinder connected to the rudders
Emergency bar
Electronic controls for engine acceleration and mechanical inverter
N.1 fixed fire fighting system by CO2 remotely
N.1 water tank of 600 lt
N.1 fresh water pump
N.1 water heater
Engine room heat and noise insulation (foam sheets with lead shield)
Wood floor covered with antiskid light alloy
N.3/4 shower pumps with floating switch in a fiberglass box easily accessible
N.3/4 electric W.C – Saninautic type
N.3/4 bathroom sinks
N.3/4 washbasin mixer
N.3/4 shower mixer with flexible
Electric plant 220V AC / 24 V DC
Main panel with terminal in engine room
Pilot console engine and electronics panels
N.2 rpm counter
N.2 oil manometers
N.2 water thermometers
N.2 reduction gear manometers
N.1 log
N.1 water level gauge
N.1 fuel level gauge
N.1 voltmeter/alternators charging
N.1 VHF
N.1 Compass
N.1 GPS/Plotter
N.Autopilot
N.1 horn
N.1 set of navigation and submersible lights
Alogen lights in all cabins
N.2 batteries 180 Ah each
N.1 shore power cable 20 Mt with American plug - QUESTO C’E’?
N.1 automatic rectifier 40 Ah (battery charger)
N.2 batteries switch
[ Anodic protection with zincs connected to a copper plate ]
[ N.2 wipers ]
[ N.1 windlass 1000 W ]
[ Hatches to engine room opens by an hydraulic cylinder ]
[ Flaps ]
[ Elettrohydraulic steering for autopilot ]
[ Hydraulic gangway (Gandola/Besenzoni type) ]
N.1 Refrigerator with Freezer tot. 160 Lt
Oven
Vitroceramic cooking plates
Marble on top of galley bar
Hanghing lockers
SS sink in stainless steel or enamel
Mixer
N.1 sofa U shape convertible in bed
Dining table
TV place
Main panel
Curtains
N.2 Hatches on the ceiling
Walls covered in cherry wood
Ceiling covered in sky panels and heat insulated
Hatches door in stainless steel and temperated glass
With double bed and separate bed or N.2 separate beds
Curtains
Hanging lockers , beds , cupboards , walls and bed tables all in cherry wood
Ceiling in sky panels
Doors in wood
Mattress and cushions
Bed covers
Carpet on wood floor
Ceiling and walls heat insulated [TORNA ?]
With double bed or N.2 separate beds
Curtains
Hanging lockers, beds , cupboards , walls and bed tables all in cherry wood
Ceiling in sky panels
Doors in wood
Mattress and cushions
Bed covers
Carpet on wood floor
Ceiling and walls heat insulated [TORNA ?]
N.1 double bed
Curtains
Hanging lockers , bed , cupboards , walls and bed table all in cherry wood
Ceiling in sky panels
Doors in wood
Mattress and cushions
Bed covers
Beauty
Carpet on wood floor
Ceiling and walls heat insulated [TORNA ?]
N.1 separate bed
Mattress and cushions
Access from hatch on the forward cabin top
Ceiling and walls heat insulated
Walls in white laminate
All furnitures lacquered
Shower box with door
Floor in teak wood
Marble on sink top
Crystal mirror
Wc
Walls in white laminate
All furnitures lacquered
Shower box with door
Floor in teak wood
Marble on sink top
Crystal mirror
Wc
Walls in white laminate
All furnitures lacquered
Shower
[Floor in teak wood ?]
Sink top
Crystal mirror
Wc
[ Stainless steel hand rail diameter 30 mm ]
[ Stainless steel anchor plate on deck ]
[ Electrical mooring winch 1000 W on aft of boat ] [1000 E NON 500]
[ 20 kg anchor with 75 mt chain diameter 8 mm ]
[ N.8 fenders with tissue glove ]
[ N.2 18 mm mooring ropes and chains 20 mt long ]
[ Stainless windshield in 8mm tempered glass ]
[ Fiberglass moulded radar arch. ]
[ Fore and aft sunbathing cushions ]
[ N.6 stainless steel mooring cleats ]
[ Top canvas with front openings and temperature sides ]
[ Back canvas ]
Detailed Photos
![]() | ![]() |
![]() | ![]() |
![]() | ![]() |
![]() | ![]() |
Packaging & Shipping
![]() | ![]() |
![]() | ![]() |
Company Profile
Shine Boating Co., Ltd. Was established in 2019, located in Shandong Province, specializing in the export of boat series.
Since its establishment, Shine Boating has been committed to the design, research and development, production, sales and service of small and medium-sized boutique yachts, and is a system solution provider of fishing boats, leisure and recreational boats, Road Runner boats, high-speed boats, yacht trailers and other products in China.
Shine Boating has a high-quality team with excellent professional technology, strong pioneering ability and rich practical experience. Based on the product design concept of "providing customers with a perfect driving experience", Shine Boating introduces the advanced yacht production technology from New Zealand, and relies on its parent company's leading domestic yacht mold precision processing technology, combined with the application of new materials, Through the introduction of advanced yacht production technology from New Zealand, relying on the parent company's leading domestic yacht mold precision processing technology, combined with the application of new materials, process innovation, etc., the company realizes the best safety performance and exquisite manufacturing of its products, so as to satisfy the needs of domestic and foreign markets. At present, the company's products cover 14 types of boats and yacht trailers, such as 485SC, 515SC, 705HT, etc., and can provide complete design and production solutions according to customers' needs, with more than 20 relevant authorized patents, an annual production capacity of 2, 000 boats, and are exported to Australia, New Zealand, Europe, North America and Southeast Asia and other countries and regions.
In the future, Shine Boating will continue to uphold the service concept of "manufacturing the most cost-effective medium- and high-end yachts", become the opener and practitioner of the dream, and strive to build China's first-class, internationally recognized by customers as an outstanding yacht manufacturing and service enterprise, so that customers can feel the color of the sea and the sky, and enjoy a happy life to the fullest.